| Date-Issued: | 07/07/2000 |
| MSDS Ref. No: | 10047 |
| Date-Revised: | 08/02/2005 |
| Revision No: | 2 |
MATERIAL SAFETY DATA SHEET
|
| ||||||||
| EZ Beads | |||||||||
1. PRODUCT AND COMPANY IDENTIFICATION
PRODUCT NAME: EZ Beads
PRODUCT CODE: 47
PRODUCT FORMULATION NAME: EZ Beads
| MANUFACTURER | ||
|---|---|---|
Auto Wax Company, Inc. |
|
|
COMMENTS: To the best of our knowledge, this Material Safety Data Sheet conforms to the requirements of US OSHA 29 CFR 1910.1200.
2. COMPOSITION / INFORMATION ON INGREDIENTS
| Chemical Name | Wt.% | CAS# | EINECS# | |||
|---|---|---|---|---|---|---|
| 2-Butoxyethanol | 3 - 8 | 111-76-2 | 203-905-0 | |||
| Propan-2-ol (isopropyl alcohol) | 1 - 5 | 67-63-0 | 200-661-7 |
3. HAZARDS IDENTIFICATION
EMERGENCY OVERVIEW
IMMEDIATE CONCERNS: May cause a slip hazard if material gets on floor.
POTENTIAL HEALTH EFFECTS
EYES: May be irritating to the eyes.
SKIN: May cause slight irritation.
INGESTION: Harmful if swallowed.
INHALATION: Prolonged or excessive inhalation may cause respiratory tract irritation.
SIGNS AND SYMPTOMS OF OVEREXPOSURE
EYES: Eye contact may cause redness, tearing and a burning sensation.
SKIN: Repeated or prolonged skin contact may cause redness and irritation.
INGESTION: Ingestion may cause nausea and irritation.
CHRONIC: not available
MEDICAL CONDITIONS AGGRAVATED: dermititis may be aggravated by excessive exposure to skin.
ROUTES OF ENTRY: include skin contact, skin absorption, eye contact , inhalation and ingestion
TARGET ORGAN STATEMENT: not available
HEALTH HAZARDS: Moderately irritating to the eyes.
PHYSICAL HAZARDS: Solutions extremely slippery when spilled.
4. FIRST AID MEASURES
EYES: Flush eye with water for 15 minutes. Seek medical attention if irritation persists.
SKIN: Remove contaminated clothing. Wash with soap and water.
INGESTION: Do not induce vomiting. Seek medical attention immediately.
INHALATION: Move to fresh air
5. FIRE FIGHTING MEASURES
FLASHPOINT AND METHOD: none
FLAMMABLE LIMITS: Not Available
AUTOIGNITION TEMPERATURE: Not Available
FLAMMABLE CLASS: Material will not burn.
EXTINGUISHING MEDIA: use water, foam, dry chemical or cabon dioxide extinguisher
AUTOIGNITION TEMPERATURE: not available
FLAMMABLE LIMIT: not available
FLASHPOINT: not available
FIRE EXPLOSION: not available
SENSITIVE TO STATIC DISCHARGE: not available
6. ACCIDENTAL RELEASE MEASURES
SMALL SPILL: Contain and collect with absorbent
LARGE SPILL: LARGE SPILLS: Shut off leak if safe to do so. Contain material to avoid run off and collect spill with absorbent.
ENVIRONMENTAL PRECAUTIONS
WATER SPILL: Avoid runoff into storm sewers and ditches which lead to waterways.
7. HANDLING AND STORAGE
GENERAL PROCEDURES: Keep out of reach of Children.
STORAGE: Do not allow to freeze
STORAGE TEMPERATURE: (35°F) minimum to (100°F) maximum
SHELF LIFE: one year
ELECTROSTATIC ACCUMULATION HAZARD: not applicable
8. EXPOSURE CONTROLS / PERSONAL PROTECTION
EXPOSURE GUIDELINES:
OSHA HAZARDOUS COMPONENTS (29 CFR 1910.1200)
| EXPOSURE LIMITS | |||||||
|---|---|---|---|---|---|---|---|
| Chemical Name | OSHA PEL | ACGIH TLV | Supplier OEL | ||||
| ppm | mg/m3 | ppm | mg/m3 | ppm | mg/m3 | ||
| 2-Butoxyethanol | TWA | 50 ppm[1] | 240 mg/m3 | 25 ppm | 121 mg/m3 | ||
| Propan-2-ol (isopropyl alcohol) | TWA | 400 ppm | 980 mg/m3 | 400 ppm | 983 mg/m3 | ||
| STEL | 500 ppm | 1230 mg/m3 | |||||
OSHA TABLE COMMENTS:
1. skin
ENGINEERING CONTROLS: Good general ventilation should be sufficient to control airborne levels.
PERSONAL PROTECTIVE EQUIPMENT
EYES AND FACE: Wear safety glasses with side shields or goggles.
SKIN: Use Nitrile/ Vinyl gloves
RESPIRATORY: NIOSH respirator - in absence of proper environmental controls.
PROTECTIVE CLOTHING: Clean, body-covering clothing
9. PHYSICAL AND CHEMICAL PROPERTIES
PHYSICAL STATE: Liquid
ODOR: glycol ether odor
APPEARANCE: Clear amber liquid
pH: ~ 3 to 5.5
PERCENT VOLATILE: Not Available
VAPOR PRESSURE: Not Available
VAPOR DENSITY: Not Available
BOILING POINT: Not Available
FREEZING POINT: ~ (32°F)
SOLUBILITY IN WATER: Will mix with water
SPECIFIC GRAVITY: ~ 0.93 to .94 gm/ml
VISCOSITY: Not Available
10. STABILITY AND REACTIVITY
STABLE: YES
HAZARDOUS POLYMERIZATION: NO
CONDITIONS TO AVOID: Oxidizing materials.
11. TOXICOLOGICAL INFORMATION
ACUTE
not available
SENSITIZATION: not available
TARGET ORGANS: not available
SUBCHRONIC: not available
CHRONIC: not available
CARCINOGENICITY:
IARC: Listed by IARC- NO
NTP: Listed by NTP- NO
OSHA: Listed by OSHA- NO
MUTAGENICITY: not available
REPRODUCTIVE EFFECTS: not available
12. ECOLOGICAL INFORMATION
ENVIRONMENTAL DATA: not available
ECOTOXICOLOGICAL INFORMATION: not available
13. DISPOSAL CONSIDERATIONS
DISPOSAL METHOD: Dispose in accordance with local, state, and federal laws.
14. TRANSPORT INFORMATION
DOT (DEPARTMENT OF TRANSPORTATION)
OTHER SHIPPING INFORMATION: Refer to bill of lading or container label for DOT or other transportation hazard classification, if any.
15. REGULATORY INFORMATION
UNITED STATES
TSCA (TOXIC SUBSTANCE CONTROL ACT)
TSCA REGULATORY: All Ingredients are on the TSCA Inventory or are not required to be listed on the TSCA Inventory
CANADA
WHMIS HAZARD SYMBOL AND CLASSIFICATION
 |
WHMIS Toxic
16. OTHER INFORMATION
PREPARED BY: Tony Casmus
REVISION SUMMARY Revision #: 2 This MSDS replaces the July 01, 2002 MSDS. Any changes in information are as follows: In Section 14 DOT Proper Shipping Name DOT Technical Name DOT Primary Hazard Class/Division Other DOT Shipping Information In Section 15 TSCA Regulatory
|
| |||||||||||||||||||||||||||||||||||||||||
MANUFACTURER DISCLAIMER: The information in this MSDS was obtained from current and reputable sources. However, the data is provided without any warranty, express or implied, regarding its correctness or accuracy. It is the user's responsibility both to determine safe conditions for use of this product and to assume liability for loss, injury, damage or expense resulting from improper use of this product.